How To Make Prints From A Tree Ring

Wondering how to make prints from a tree ring? Check out this DIY project where I show you how I took a tree stump and turned it into a tree ring print!

I made some custom artwork for my house by turning a tree stump into a stamp and imprinting the growth rings on a sheet of paper. Let me show you how I did it.

how to make prints from a tree ring00 00 04 05still001
How To Make Prints From A Tree Ring 18

Things I Used in This Prints From A Tree Ring Project:

how to make prints from a tree ring00 00 21 15still004
How To Make Prints From A Tree Ring 19

I first grabbed a tree from my property. This is mesquite. It had been cut with a chainsaw. And while not too rough, the surface wasn’t perfectly flat. So I used my Triton Belt Sander to work on getting it flat. However, while it was working, it was taking a bit too long.

how to make prints from a tree ring00 00 33 22still005
How To Make Prints From A Tree Ring 20

So I decided to take down the bulk of the unevenness with my Triton Electric Planer instead. I originally used my small planer to hit the high spots. Then after getting the surface roughly down to the same level, I switched to using my larger Triton 7″ Planer.

how to make prints from a tree ring00 01 06 19still007
How To Make Prints From A Tree Ring 21

Then, after a few passes with the belt sander again, I had a smooth surface that was nice and flat. It’s important to get a nice flat surface so that your paper can hit everywhere on the stump and transfer the ring pattern.

how to make prints from a tree ring00 01 19 19still008
How To Make Prints From A Tree Ring 22

So now the stump is nice and smooth. But in order to make the print work, you need high and low spots. When looking at a tree ring there are portions that are soft wood and hard wood. The idea to make a stump into a stamp is to use heat to slightly burn away the soft wood so that the harder rings are pronounced.

I decided to upgrade to my propane bottle torch to speed up the process. I was aiming to get a nice and even burn without charing the surface.

how to make prints from a tree ring00 01 43 09still009
How To Make Prints From A Tree Ring 23
how to make prints from a tree ring00 01 51 21still010
How To Make Prints From A Tree Ring 24

Afterwards, I used a wire brush to remove the debris I created. If you can run your fingers over the surface and feel the distinct tree rings, then you’ve done enough.

how to make prints from a tree ring00 02 02 26still011
How To Make Prints From A Tree Ring 25

Then I let the stump fully cool down because up next is applying ink and you dont want the stump to be hot when doing so.

I’d first use a spray bottle and wet down the surface of the stump. This will help the paint from soaking in and instead remain on the surface. I’m using acrylic ink and applied it using a foam roller.

how to make prints from a tree ring00 03 56 13still012
How To Make Prints From A Tree Ring 26

After making sure the entire surface was coated, I lined up my paper and set it in place, being careful not to shift it side to side once it was down.

how to make prints from a tree ring00 04 06 17still013
How To Make Prints From A Tree Ring 27

I would then carefully peel the paper up from the stump to reveal the outcome. Pretty neat!

how to make prints from a tree ring00 04 19 03still014
How To Make Prints From A Tree Ring 28

I was having so much fun with the process that I decided to make some more, playing with the amount of ink I used. I found that if you used too much ink, the image came out smudged looking. And if you don’t apply too much, the image comes out faded and the paper sticks to the stump.

how to make prints from a tree ring00 04 43 25still016
How To Make Prints From A Tree Ring 29
how to make prints from a tree ring00 04 55 15still017
How To Make Prints From A Tree Ring 30

Once I had the process down, I started playing with color. I used water to rinse in between colors. Then I’d apply a new color and play.

how to make prints from a tree ring00 05 14 17still018
How To Make Prints From A Tree Ring 31
how to make prints from a tree ring00 05 20 17still019
How To Make Prints From A Tree Ring 32

Then, after the prints were fully dry, I placed them in a frame and hung them up. Now I have some custom artwork in my house that I absolutely love.

Tree Ring Framed 1
How To Make Prints From A Tree Ring 33
Tree Ring Framed 1
How To Make Prints From A Tree Ring 34

Be sure to watch the video for an even better tutorial. Hopefully you’ve enjoyed this one. I will see you on my next project!

If you haven’t already, don’t forget to sign up at the top of this page for my newsletter so you don’t miss new projects!

(Most of the links listed above are affiliate links. As an Amazon Associate I earn from qualifying purchases. Thank you for supporting me in this way.)

Share This Project!

Twitter
Facebook
Pinterest
LinkedIn
Tumblr
Email

Related Projects