Easy DIY Hardware Storage Shelf

Thinking about building a DIY hardware storage shelf? Check out this easy DIY project where I built a storage shelf for a lot of my hardware!
Just like a lot of other people I had a bunch of screw boxes just hanging out and in the way. Ok…so eight doesn’t seem like that many, but when they were taking up space on my workbench, it seemed like a lot. Regardless. I made this awesome shelf to hold them. : )
diy hardware storage shelf 17diy hardware storage shelf 16

Inspiration: 

I saw this photo on pinterest and loved the idea but tweaked it just a little to simplify it some.
diy hardware storage shelf 15
Just to kinda give you another option if you are looking for hardware storage ideas I also liked this one…

and it was the one I was going to go with except I didn’t like the idea of throwing away the perfectly good (and already labeled) containers the screws come in just to have a bigger container in it’s place. But! It is a good option to consider and you could use the same steps below and just skip my step about making shelves.

As for mine….I built it from scraps so this one only holds 10 boxes, but I could easily make another one and put it either beside or under this one. : ) You can make yours as long as you want though; the same steps will apply.

Here are the steps if you want to make your own

Actually, before we get started (just so I don’t have to keep inserting it) just note: a screw box is 3 1/2″ deep, 4 1/2″ wide, and 1 3/4″ tall.

1) I have a stack of 23″ long scrap pine 1xs in my shop from making growth chart rulers so I grabbed one and lined out my marks. I came in 1/4″ then made a mark every 2 1/4″ after that. I would first mark exactly where the 1/4″ mark fell (center markings below) but then also mark 1/8″ less (the left lines) and 1/8″ more (the right lines). I did this because I knew I was going to use 1/4″ material for the shelves and this would give me a better visual for cutting those slots.

diy hardware storage shelf 13

2) I put my dado blades on my table saw and just cut where my lines were. It might be easier for you if you transfer your marks to the side of the wood but I just looked at my marks on the top then lined it up to the blade and pushed it through with my miter gauge.

diy hardware storage shelf 11

Note: If you aren’t familiar with dado blades, they are just blades that make cutting slots like these easier. If you don’t have a set then you can use either your table saw or circular saw. The blades width is 1/8″ so you would need to make a pass then line up your piece again to make a second pass. If you do it this way you need to make sure you don’t overlap the passes or your slot won’t be 1/4″ and your shelves won’t fit.

3) To make it to where I could easily grab the box I wanted to make the sides 2 1/2″ deep. I set the fence on my table saw and ripped two strips.
diy hardware storage shelf 10

By doing it this way the slots line up perfectly with their counter slot.

diy hardware storage shelf 9

4) Next I cut 11 shelves that are 5 1/2″ x 2 1/2″. Note: The width of your shelves will be determined by how deep you make your dadeo cuts. To figure out the measurement you can put a box in between the two sides then measure from the end of the left slot to the end of the right.

diy hardware storage shelf 8

….Eh. WilkerDon’t: While I was testing out my slots I actually ended up breaking those slim end pieces. …Yeah. I mightn’t yelled said a few unladylike words at that point. So learn from my lesson and be careful with those ends.

5) I whittled up new ones then used my Kreg pocket jig to put in four pockets. If you also use pockets be sure you are facing them the correct way. Since these slots line up with one another, you can’t just flip your piece over if you put in your pockets upside down. ; )

diy hardware storage shelf 7

Note: Instead of cutting and attaching a back piece, I made these pockets so I could attach the unit directly to my shop wall. If you don’t have a Kreg, or don’t like the design, then cut a back and that will allow you to either attach a hanger on the back or screw it in from the inside through the back.

6) Next I put in the two end shelves first then put in the rest. I used the rubber end of my hammer here to help it along. Since it’s such a snug fit I didn’t use wood glue.

diy hardware storage shelf 6

7) Then I picked out a spot on my wall and put four screws in those pockets I made in step 5.

diy hardware storage shelf 5
So any time I need a box I can just grab whichever one I want and pull it out.
diy hardware storage shelf 16
Last things last (is that a saying?), I decided to put some paint on it…
diy hardware storage shelf 4IMG 0068

Cool. Better no?

Total Time: 1 hr

Total Cost: $0

: D Just an update on this side of my shop. It is slowly but surely coming along! Between cleaning out a bunch of Cody’s junk, building my paint cabinet, rolling cabinet, and now hardware rack….yeah….I’m really loving this side. (You can go back to my earlier posts and look in the background to see just how far it’s come.)

diy hardware storage shelf 2

Eh. But then this corner ruins it. : / Maybe next weekend I can get Cody to make room in his shop for his cubby hole thing so I can start on that corner and back wall.

diy hardware storage shelf 1

Be sure to subscribe if you’re interested in seeing what projects I come up with next! I hope everybody has a great week.

Share This Project!

Twitter
Facebook
Pinterest
LinkedIn
Tumblr
Email

Related Projects